"Ron" <BigELilE05@[EMAIL PROTECTED]
> wrote in message
news:1891bc14-833b-49d3-925e-c49589ea997a@[EMAIL PROTECTED]
Jul 3, 4:40 am, "Arfa Daily" <arfa.da...@[EMAIL PROTECTED]
> wrote:
> "nipperchipper" <nipperchip...@[EMAIL PROTECTED]
> wrote in message
>
> news:J-SdnUraL6u1MPbVnZ2dnUVZ_hOdnZ2d@[EMAIL PROTECTED]
>
>
>
> > "Ron" <BigELil...@[EMAIL PROTECTED]
> wrote in message
>
>news:93b8e32f-997a-48b9-91fa-858c504de3b8@[EMAIL PROTECTED]
> >>I have two Panasonic VCR's, model numbers PV-V4540 and PV-9450.
>
> >> They are almost idenical on the outside and very simular on the
> >> inside.
>
> >> The "newer" model - PV-V4540 - seems to have a head going bad from
> >> everything I've read.
>
> >> The PV-9450 works fine, but doesn't have the features that the PV-
> >> V4540 has.
>
> >> I would like to install the head unit from the PV-9450 (the older
one)
> >> in the PV-V4540 (the newer one).
>
> >> They look the same, but are they the same? And if I swap the
> >> headunits, will the alignment be the same?
>
> >> Here are pics of the head units. The one thing that I wondering about
> >> is the "arm" on the center post of the (newer) PV-V4540...what is
> >> that?
>
> >> PV-V4540 head unit
> >>http://i126.photobucket.com/albums/p96/bigelile/IM002417-1.jpg
>
> >> PV-9450 head unit
> >>http://i126.photobucket.com/albums/p96/bigelile/IM002411-1.jpg
>
> >> PV-V4540 face
> >>http://i126.photobucket.com/albums/p96/bigelile/IM002414-1.jpg
>
> >> PV-9450 face
> >>http://i126.photobucket.com/albums/p96/bigelile/IM002413-1.jpg
>
> > from the parts list pvv4540 uses the beliow listed upper cylinder head
> > VEGS0427 ( A )
> > VEGS0428 ( B,C,D )
> > VEGS0429 ( E,F )
>
> > pv9450 uses
> > VEHS0571 ( A )
> > VEHS0570 ( B,C )
> > VEHS0567 ( D,E )
> > not much help but swapping may not hurt
>
> Given that info, it's probably not going to work right. Hifi sound is
> critical of correct head performance, so if there are any specification
> differences between the head drums, there will likely be a problem.
Well, that is an understatement.
Put the head drum from the older working VCR into the newer one, there
was no signal on the face plate for "HiFi".
So I put it back into the - what was working unit - and NO HiIFi.
Don't know what happened, but the newer VCR fried something in the
older ones head drum.
Now I have 2 Panasonics that don't work. :(
I feel that to be highly unlikely, as the coupling between the heads and
the
amplification electronics is completely isolated by a rotary transformer,
the primary of which is in the upper head drum, and the secondary, in the
lower.
Far more likely is that the screw-holes are not offset, and you have
managed
to get the upper drums 180 degrees out on the centre spindle. Unscrew the
formerly good one again, and try turning it through 180 degrees, and see
if
the holes still line up. If they do, screw it down again, and retest. If
that gets you back to working, then try your swap again, taking note of
the
same potential problem.
Arfa
|
